Installing the Dialogic®
Brooktrout® T1/E1 PCI
Express Fax Board (Single
Span)
Part Number: 64-1193-02
The
Dialogic® Brooktrout®TR1034 T1/E1
combination PCI Express boards (“TR1034” or
“TR1034 Fax Board(s)”)
are low profile, half length,
single slot, PCI Express serial I/O bus-compatible
boards with T1/E1 capabilities. The TR1034 delivers
33.6 Kbps (V.34) fax transmission speeds, up to 30
fax channels per board, and an on-board T1/E1
interface (see Figure 4).
The TR1034 T1/E1/IP PCI Express boards use 3.3V
and 12.0V power from the serial bus and can be
inserted in x1, x4, x8, or x16 bus (signaling) slots.
You need a separate fax application to use the
TR1034 Fax Board. Please contact your application
provider (normally a third party vendor) for the
correct operating system driver, supporting files,
and firmware.
System Requirements
This board must be installed in an enclosure that
meets the following specifications.
A Pentium 4 or later host processor
A x1, x4, x8, or x16 PCI Express serial I/O bus
slot. See Recognizing PCI Express Slots for more
information.
Temperature: 0°C - 50°C
Humidity: 10% - 90% (noncondensing)
Power requirements:
2.6 W at 3.3 V
2.4 W at 12 V
5 W total
Setting the Module Number
You must set each TR1034 Fax Board to a unique
module number to identify the resources associated
with a specific board in a multi-board system. Use
the rotary switch (Figure 1) to set the module
number for each TR1034 Fax Board (see location in
Figure 2). The available settings are 2 - F (0 and 1
are reserved).
Figure 1 Rotary Switch
Figure 2 Dialogic
® Brooktrout® TR1034 T1/E1 PCI
Express Fax Board
Safety Compliance Statements
Install this board only in UL Listed equipment
that has instructions stating that the user may
install and remove accessory boards.
Disconnect any interface cables from this board
before removing the cover of the equipment.
Installing the Dialogic® Brooktrout® TR1034
Fax Board
To install the board:
1. Power off the computer.
2. Remove the computer cover. If the system has a
board hold-down bar, remove it as well.
3. Locate an unused PCI Express bus slot (see
Figure 3).
4. Holding the TR1034 Fax Board at each top
corner, carefully insert the PCI Express Board
Edge connector firmly into the PCI Express slot.
5. Screw the board’s mounting bracket securely to
the computer's frame. See Figure 2.
6. Replace the computer cover.
7. Turn on the computer.
The board status LED (see Figure 2)
continuously flashes yellow when you turn the
computer on.
Note: Dialogic® Brooktrout® Fax Boards should not be
present in the computer during the installation of any
operating system. The operating system can
misinterpret the board as being some other device, with
unpredictable consequences.
Recognizing PCI Express Slots
The PCI Express slots in the computer chassis
appear as black slots. Figure 3 shows the different
variations of PCI Express slots. You can insert the
Dialogic® Brooktrout® TR1034 Fax Board into any
of the PCI Express slots shown in Figure 3.
Figure 3 PCI Express Serial Bus Slots
Caution: A small amount of static electricity can
destroy the sensitive components on your board.
To prevent static damage, always connect yourself
to ground using a ground strap before touching a
circuit board. Handle boards only by the edges or
metal mounting brackets and transport boards in
an anti-static bag.
(114 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels