Dialogic Digital Network Interface Board DN/I601TEPHMP Manuel d'utilisateur télécharger pdf

Part number: 64-0084-02

Dialogic

DN/I601TEPHMP Digital

Network Interface Board

Installation Guide

1. Product Description

The Dialogic

DN/I601TEPHMP Digital Network

Interface Board (“board”) is a high-density, high-

performance, network interface board in a universal

PCI form factor with two T1/E1 digital network

interfaces. This board is designed to be used with

Dialogic

Host Media Processing (HMP) software

(Release 2.0 or higher).

The DN/I601TEPHMP Digital Network Interface

Board includes the following components:

RJ-48C Jacks: Two connectors to a T1 or E1 trunk.

General Network Interface Alarm LED: When lit,

indicates an alarm condition is present on one or

more of the trunks.

Reset LED: When lit, indicates that the board is in

the reset state.

Power LED: When lit, indicates power is on.

SW1: Rotary switch used to set board identification

(Linux system only).

Alarm/Status LEDs: A set of four LEDs for each

trunk. During power-up, the LEDs indicate Power

On Self Test (POST) status. After the board is

started, the green, yellow, and red LEDs indicate

normal operation or Carrier Failure Alarms (CFAs)

for each trunk as shown in the following table. The

Loopback LED indicates when the respective

trunk is in loopback mode.

Green Yellow Red Conditions

ON OFF OFF Normal Operation

OFF OFF ON Loss of Signal (LOS)

ON OFF ON Red Alarm

ON ON OFF Yellow Alarm/Remote Alarm

Indicator (RAI)

ON ON ON Alarm Indicator Signal (AIS)

CT Bus Connector: Connector to CT Bus.

Optional ISA Edge Retainer: Bracket used to

install board in an ISA form factor PCI slot.

P5: CT Bus Termination Jumper Block. Factory

default is unterminated. Signals must be

terminated only on boards at each end of an

optional CT Bus cable.

JP3X11 and JP4X11: Power-off Default Front End

Loopback for trunk 1. Factory default is enabled

(jumper clips installed).

JP3X12 and JP4X12: Power-off Default Front End

Loopback for trunk 2. Factory default is enabled

(jumper clips installed).

JP5: Boot up Default Front End Loopback. Factory

default is enabled (jumper clip removed).

Universal PCI Bus Connector: Connector to

universal PCI Bus slot.

Additional Information

Additional information about the DN/I601TEPHMP

Digital Network Interface Board is available from a

number of sources.

The product data sheet, available at

http://

www.dialogic.com/products/list.asp

, provides a

functional description as well as information about

applications and configurations, features, and

technical specifications.

Refer to the Release Guide and the online Release

Update for your Dialogic

Host Media Processing

(HMP) software release to verify that the DN/

I601TEPHMP Digital Network Interface Board is

supported in the release and for information on any

new features or issues that may relate to it.

The Regulatory Notices document that is packed

with each DN/I601TEPHMP Digital Network

Interface Board contains safety warnings and

national requirements for proper operation of

telecommunications equipment.

2. Before You Begin

Protecting the Board from Damage

CAUTION: All computer boards are sensitive to

electrostatic discharge (“ESD”). Handle all static-

sensitive boards and components at a static-safe

work area, and observe anti-static precautions at all

times.

If you are not familiar with ESD safety precautions,

visit http://dialogic.com/support/hwinstall to learn

more.

Unpacking the Board

CAUTION: Do not remove the board from the anti-

static packaging until you are ready to install it.

Observe proper anti-static precautions at all times.

Unpack the board according to the following steps:

1. Prepare a static-safeguarded work area.

2. Carefully remove the board from the shipping

carton and static-shielding bag. Handle the

board by the edges and avoid touching the

board's components.

3. Lay the board on the static-safe work surface.

Note: Place boards in static-shielding bags when

carrying boards from station to station.

Configuring the Board

The following can be configured on the board:

■

Board ID

■

CT Bus Termination

■

Power-off Default Front End Loopback

■

Boot Up Default Front End Loopback

Setting the Board ID

The device driver assigns board instance numbers

in ascending order (beginning with 0) as it detects

each board in your system. A board instance

number is the identification (ID) number used by the

Dialogic

Host Media Processing (HMP) software to

recognize the board.

Note: If you add or remove a board, the system

may change the existing board instance numbers,

depending on the PCI bus and slot number where

the board is installed or removed.

In a Windows system, leave SW1 (see Physical

Layout) set to the factory default of 0 to let the

system automatically assign board instance

numbers by PCI bus slot number. After the hardware

and the Dialogic HMP software are installed, refer to

the Dialogic

Configuration Manager (DCM) to

retrieve the assigned board instance ID number(s).

DCM is a utility that enables you to add new boards

to your system, start and stop system service, and

work with board configuration data. This utility can

be accessed from the Start menu in the Dialogic

HMP software program folder. For more information

about board identification, see the DCM online help.

In a Linux system, you must set SW1 to a unique

number for each installed board. Use a non-

magnetic screwdriver to turn SW1 to one of 16

board settings, 0–9 or A–F. After the hardware and

the Dialogic HMP software are installed, refer to the

proper configuration files to retrieve the assigned

board instance ID number(s). For more information

about Linux configuration files, see the Dialogic

HMP software release documentation.

Setting CT Bus Termination

This section applies if you are using a CT Bus cable

to connect your board to other boards in the system.

Bus signals are terminated when the CT Bus jumper

clip is installed. To terminate bus signals, install a

jumper clip on the pair of CT Bus termination pins

only on boards located at each end of the bus cable.

Factory default is unterminated (jumper clip

removed).

The following figure shows the pair of pins used for

CT Bus termination. Refer to P5 in the Physical

Layout figure for the location of the jumper block.

CT Bus

Termination

CT Bus

Connector

Physical Layout

RJ-48C Jacks

General Network

Alarm LED

Universal PCI

Bus Connector

(on reverse

ide of board)

CT Bus

Connector

SW1

tional ISA Edge

Retainer

Reset LED

Power LED

JP5

Alarm/Status LEDs

JP3X12

and JP4X12

JP3X11

and JP4X11

Red

Yellow

Green

Loopback

1 2

Résumé du contenu

Page 1 - Network Interface Board

Page 2 - 2 JP3X12 and JP4X12

Setting Power-off Default Front End LoopbackWhen the system shuts down (powers off), the board enables analog loopback to the connected trunk line(s).

Commentaires sur ces manuels

Pas de commentaire

Dialogic Digital Network Interface Board DN/I601TEPHMP Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Dialogic Digital Network Interface Board DN/I601TEPHMP. Dialogic Digital Network Interface Board DN/I601TEPHMP User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Dialogic Digital Network Interface Board DN/I601TEPHMP