Dialogic SS7G21 Manuel d'utilisateur

www.dialogic.comDialogic® SS7G21 and SS7G22 Signaling ServersHardware Manual

10Chapter 1 Warnings and CautionsCaution Anti-Static Handling Procedures: The product contains Electrostatic Sensitive Devices (ESDs), which may be pe

11Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Chapter 2: Introduction2.1 Purpose This manual addresses the hardware aspects

12Chapter 2 IntroductionA list of product variants to which this manual applies can be found in Section 2.11, “Applicability” on page 14. 2.3 Power Su

13Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Depending on the variant, an SS7G21 can contain one of the following: • Up to t

14Chapter 2 IntroductionFor more information on Dialogic® SS7 products and solutions, visithttp://www.dialogic.com/support/helpweb/signaling. 2.11 App

15Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Chapter 3: Product Specification3.1 DC Power Supply ModuleThe DC Power Supply

16Chapter 3 Product Specification3.4 PCM InterfaceThe PCM interface specification is described as follows: • Ports: The number of ports depends on the

17Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 73.7 Serial Port (COM2)The serial interface port specification is described as f

18Chapter 3 Product Specificationalarms is given in the appropriate SS7G2x <Operating Mode> User Manual. Section 2.10, “Related Information” on

19Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 73.10 Physical SpecificationsThe physical specifications of the SS7G21 and SS7G2

2Copyright© 2004-2008 Dialogic Corporation. All Rights Reserved. You may not reproduce this document in whole or in part without permission in writing

20Chapter 3 Product Specification

21Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Chapter 4: Regulatory Specifications and DeclarationsTopics covered in this ch

22Chapter 4 Regulatory Specifications and Declarations4.1.3 Telecommunications ComplianceUSA:TIA/EIA-IS-968 – July 2001 (SPCI, therefore SS7G21) TIA-9

23Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 74.2 Declarations of the Manufacturer or ImporterThe International Declarations

24Chapter 4 Regulatory Specifications and Declarations Declaration of ConformityNo: D0006Revision 01The equipment described below is declared to be in

25Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 74.2.1 CE Declaration of Conformity – European Economic AreaThe Products carry t

26Chapter 4 Regulatory Specifications and Declarations[Malti]Hawnhekk, Dialogic Corporation, jiddikjara li dan SS7G21, SS7G22 jikkonforma mal-h-tig·ji

27Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7A plug and jack used to connect this equipment to the premises wiring and telep

28Chapter 4 Regulatory Specifications and Declarations4.3 Essential Compliance InformationThis section documents miscellaneous points that should be o

29Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Note that for some geographic regions, and subject to limitations, the T1/E1 po

Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual3Contents Part 1: User’s Guide...

30Chapter 4 Regulatory Specifications and Declarations

31Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Chapter 5: Hardware Description5.1 OverviewThe Dialogic® SS7G21 and SS7G22 pro

32Chapter 5 Hardware Description5.2 Front PanelFigure 3 shows the front panel controls, indicators and switches and Table 3 summarizes their functions

33Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 75.3 Back PanelFigure 4 shows the back panel connectors and Table 4 summarizes t

34Chapter 5 Hardware Description5.4 Rack Mounting OptionsA number of optional mounting arrangements are available for the Dialogic® SS7G21 and SS7G22

35Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Chapter 6: InterfacesThis section provides connector pinout details for all us

36Chapter 6 InterfacesFigure 6. PCM Ports on SPCI4 BoardsFigure 7. PCM Ports on SS7HDP BoardsThe T1/E1 ports on the SS7 Signaling Boards are Safety Ex

37Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Figure 8. SS7 Serial Interface Connector (Aux on SPCI2S)The SS7 serial interfac

38Chapter 6 InterfacesAn SS7 Serial Interface Port Splitter Cable is available, DKL26 (see Chapter 12, “Part Number Reference”). This is a cable that

39Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 76.7 Serial Port (COM2) One serial port (COM2, marked 10101) is provided on the

4Contents7 Warnings and Cautions ...438 Tools and Supplies Ne

40Chapter 6 Interfaces6.8 AlarmsThe alarms port interface is a 15-way male DB15 connector (see Figure 11). This connector allows remote notification o

41Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Part 2: Service Technician’s Guide

42Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7

43Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Chapter 7: Warnings and CautionsWARNING QUALIFIED SERVICE TECHNICIAN OPERATION

44Chapter 7 Warnings and CautionsWARNING IF AC POWER SUPPLIES ARE INSTALLED:MAINS AC POWER DISCONNECT: The AC power cord(s) is considered the mains di

45Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7WARNING IF DC POWER SUPPLIES ARE INSTALLED:ISOLATION: The product with DC input

46Chapter 7 Warnings and CautionsCaution Anti-Static Handling Procedures: The product contains Electrostatic Sensitive Devices (ESDs), which may be pe

47Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Chapter 8: Tools and Supplies NeededProcedures in Part II of this manual requi

48Chapter 8 Tools and Supplies Needed

49Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Chapter 9: Product Installation and Hot-Swap ActionsThis chapter describes act

Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual516 Unlocking and Removing the DC Power Supply Module ...

50Chapter 9 Product Installation and Hot-Swap Actions— Configure the product. 10.When installation is complete and the system is operating as intended

51Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7• Replacement of Power Supply Module in AC Products The general actions require

52Chapter 9 Product Installation and Hot-Swap ActionsFigure 13. DC Power Supply Module Terminal BlockThe product is supplied with an insulating cover

53Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Figure 15. DC Power Terminal LugWhen selecting an appropriately sized power wir

54Chapter 9 Product Installation and Hot-Swap ActionsNote: For DC powered products, the power source should be disconnected from any module while it i

55Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Note: For AC powered products, the power source may be connected and turned on

56Chapter 9 Product Installation and Hot-Swap ActionsAn SS7G20SHDD may be used in any SS7G2x Signaling Server, however, it requires a valid System Lic

57Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Figure 18. Replacing the Hard Disk Drive2. To unlock the carrier from the chass

58Chapter 9 Product Installation and Hot-Swap Actions

59Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Chapter 10: Working Inside the ProductThis chapter describes actions that must

6Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Part 1: User’s Guide

60Chapter 10 Working Inside the Product10.3 Removing and Installing the Top CoverRemoval of the Top Cover is necessary when installing or removing int

61Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Figure 19. Top Cover Removal and Installation10.4 Internal Product LayoutThe la

62Chapter 10 Working Inside the Product10.5 SS7 Signaling BoardsSS7G21 and SS7G22 are available with up to three SS7 Signaling Boards installed. The t

63Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Note: If only two SPCI Signaling Boards are installed, then the middle position

64Chapter 10 Working Inside the ProductNote: If only two SS7HDP Signaling Boards are installed, then the middle position (No.2) should remain empty.Fi

65Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 72. To remove the Signaling Board Subsystem, un-latch it from the chassis by pla

66Chapter 10 Working Inside the ProductFigure 24. Cable Tie Securing SS7 Signaling Board to Card Keep FrameCT Bus Cable NotesNote: When the CT Bus cab

67Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7To replace the back-up battery, follow this procedure:1. Observe the Safety and

68Chapter 10 Working Inside the Product

69Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Chapter 11: International Warnings11.1 WARNING: EnglishcontinuedThe power supp

7Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Chapter 1: Warnings and CautionsWARNING QUALIFIED SERVICE TECHNICIAN OPERATIONS

70Chapter 11 International WarningsWarning: English (continued) A microprocessor and heat sink might be hot if the system has been running. Also, ther

71Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 711.2 AVERTISSEMENTS: FrançaissuiteLe bloc d'alimentation de ce produit ne

72Chapter 11 International WarningsAvertissements : Français (suite)Afin de permettre le refroidissement et l'aération du système, réinstallez t

73Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 711.3 WARNUNG: DeutschFortsetzungDas Netzteil dieses Computers enthält keine wa

74Chapter 11 International WarningsWarnung: Deutsch (Fortsetzung)Um eine ordnungsgemäße Kühlung und Belüftung zu gewährleisten, sollten Sie stets die

75Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 711.4 AVVERTENZA: ItalianocontinuaL'alimentatore contenuto nel computer no

76Chapter 11 International WarningsAvvertenza: Italiano (continua)Per evitare che il sistema si surriscaldi e per garantire una ventilazione adeguata

77Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 711.5 ADVERTENCIA: EspañolcontinuaciónLa fuente de alimentación de este product

78Chapter 11 International WarningsAdvertencia: Español (continuación)Para obtener una ventilación y un flujo de aire adecuados, reinstale siempre la

79Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Chapter 12: Part Number ReferenceTable 15 shows the Dialogic® SS7G2x product I

8Chapter 1 Warnings and CautionsWARNING IF AC POWER SUPPLIES ARE INSTALLED:MAINS AC POWER DISCONNECT: The AC power cord(s) is considered the mains dis

80Chapter 12 Part Number Reference Table 16. Expansion Options or Spare AssembliesProduct ID DescriptionSS7SPCI2SQ SS7 Signaling Board, 4 SS7 links, 2

81Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Chapter 13: Software Licensing InformationThis chapter gives important informa

82Chapter 13 Software Licensing Information

83Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7Appendix AA.1 Connecting to V.11 (V.35-Compatible) SS7 LinksThis appendix discu

84Appendix A A.1.2.1 Connecting an SPCI2S to an M34 Block ConnectorThe following table provides information on connecting an SPCI2S (working as a DTE)

85Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7A.1.3 ClockingPhysically, the SPCI2S has two sets of clock pins for each serial

86Appendix A

87Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7GlossaryCT Bus A time division multiplex (TDM) bus that provides 1024, 2048, or

88Glossary

89Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7IndexAAC power supply modulehot-swap 55installation of 8, 50installing a secon

9Dialogic® SS7G21 and SS7G22 Signaling Servers Hardware Manual Issue 7WARNING IF DC POWER SUPPLIES ARE INSTALLED:ISOLATION: The product with DC input

90IndexGgrounding 8, 9, 33, 35, 51Hhard disk drivebacking up the system 56description of 12location of in chassis 62replacing the hardware 56restoring

91SS7AM1 Programmer’s Manual Issue 7for SS7 serial interface ports 38SS7 serial interface portlocation of 36see also "V.11 (V.35-compatible) port